MEB 590 Module C Rate Charging Power Explained

Short answer: At 1C, an MEB 590 module draws or delivers 227 A and approximately 6.66 kW. A full charge or discharge at that rate takes around one hour; at 80 % depth of discharge, around 48 minutes. In a series string the current stays at 227 A regardless of how many modules are connected, so cables and chargers are sized to that figure.

Understanding the C rate of a battery module is straightforward once you have the capacity figure in front of you. For the MEB 590 module this article uses the catalogue values directly: 227 Ah nominal capacity, 29.36 V nominal voltage, 6.66 kWh usable energy, and a voltage window of 22.4 to 34.8 V. All calculations below follow from those figures. If a datasheet figure differs, the datasheet governs.

What 1C means for the MEB 590 module

The C rate expresses charge or discharge current as a multiple of the module's rated capacity. For a module with a nominal capacity of 227 Ah, 1C is simply 227 A. That relationship holds regardless of the number of modules in a system.

A full charge or discharge at 1C takes one hour by definition. At 80 % depth of discharge, the energy throughput is 80 % of the nominal figure, so the duration at the same current shortens proportionally:

0.8 × 60 min = 48 minutes

The 80 % DoD figure is the standard sizing basis for cycle-life calculations; for context, see MEB 590 module cycle life at 80 % DoD.

Power at 1C: the calculation

Power is voltage multiplied by current. Using the nominal voltage and the 1C current:

29.36 V × 227 A = 6,664 W ≈ 6.66 kW

This matches the catalogue energy figure of 6.66 kWh, which confirms internal consistency: a module that stores 6.66 kWh and is discharged at 6.66 kW will be exhausted in one hour. The small rounding difference between 6,664 W and 6.66 kW is a rounding artefact in the nominal voltage.

Note that the actual terminal voltage varies across the charge window (22.4 to 34.8 V), so instantaneous power will differ from this nominal figure at the top and bottom of the range. The catalogue value of 6.66 kWh and the 1C current of 227 A are the design-point references. Whether a specific application sustains that rate continuously, and for how long at temperature, is governed by the datasheet, not the catalogue.

Series strings: voltage rises, current stays fixed

The MEB 590 module is designed for pack assembly, and in practice several modules are connected in series to reach the system voltage required by an inverter or drivetrain. A worked example with 14 modules in series illustrates the key point about current:

Parameter Single module 14S string
Nominal voltage 29.36 V 14 × 29.36 V = 411 V
Voltage window 22.4 to 34.8 V 314 to 487 V
Capacity (Ah) 227 Ah 227 Ah
Energy 6.66 kWh 14 × 6.66 kWh = 93.2 kWh
1C current 227 A 227 A
Power at 1C ≈ 6.66 kW 14 × 6.66 kW ≈ 93 kW

In a series circuit, every module carries the same current. Adding modules in series increases the string voltage and therefore the total power, but it does not change the current. This is the governing principle for cable and charger selection: the conductor and the charging source must be rated for 227 A, not for 227 A multiplied by the number of modules.

For a 14S string the power at 1C is:

411 V × 227 A ≈ 93 kW

That is the power that the charger must supply, and the power the string can deliver to a load, at the nominal 1C rate.

Full module dimensions and electrical interface details are covered in the MEB 590 module specifications, and format context is available on the 590 format page.

1C as a continuous catalogue rating

The catalogue lists 1C as a continuous charge and discharge rate. This is a design-point figure: it describes what the module is specified to do on a sustained basis. Peak rates above 1C may be possible, but no peak figure appears in the catalogue entries referenced here. Where a higher rate is relevant to an application, the datasheet is the only authoritative source for the permitted duration, the temperature conditions and any derating that applies.

Thermal management interacts directly with sustained high-current operation. The module relies on its cooling interface to maintain cell temperature within specification. That topic is covered separately in the MEB 590 module cooling guide.

Cable and charger sizing: the practical takeaway

For a system designer, the 1C current figure of 227 A is the input to conductor sizing, connector selection and charger specification. The key points are:

  • The current through every module in a series string is 227 A at 1C, regardless of string length.
  • The charger must be rated for the full string voltage (22.4 × n to 34.8 × n V) and for 227 A.
  • Derating for temperature, cable length and installation method follows the applicable electrical standard. The IEC publishes installation and safety requirements for stationary battery systems under IEC 62619, which covers lithium secondary cells in stationary applications.
  • The EU Battery Regulation 2023/1542, available via EUR-Lex on europa.eu, sets documentation and due-diligence requirements that affect procurement but not the electrical sizing calculation itself.

For stationary and second-life applications of the MEB 590 module, the energy storage application overview provides further context on how modules are integrated into cabinet and containerised systems.

Frequently asked questions

What is the 1C current for an MEB 590 module?
The 1C current for an MEB 590 module is 227 A, equal to its nominal capacity of 227 Ah. This figure applies to both charge and discharge and is the reference point for cable sizing, charger specification and all C-rate calculations for this module.

What power does an MEB 590 module deliver at 1C?
At 1C and nominal voltage, an MEB 590 module delivers approximately 6.66 kW: 29.36 V × 227 A = 6,664 W. Because terminal voltage varies across the 22.4 to 34.8 V window, actual instantaneous power will differ at the top and bottom of the charge range.

How long does it take to charge an MEB 590 module at 1C?
At 1C, a full charge from empty takes approximately one hour. At 80 % depth of discharge, the equivalent energy throughput takes around 48 minutes (0.8 × 60 min). Exact duration under real conditions is governed by the datasheet, including temperature limits.

Does connecting MEB 590 modules in series increase the current?
No. In a series string, every module carries the same current. Connecting 14 modules in series raises the string voltage to approximately 411 V nominal and the power at 1C to approximately 93 kW, but the current remains 227 A. Cables and chargers are therefore sized to 227 A, not to a multiple of it.

Where does the 1C rating apply: charging, discharging or both?
The catalogue lists 1C as a continuous rating for both charge and discharge. Whether a specific application can sustain that rate and for how long depends on the datasheet conditions, including temperature and any derating the manufacturer specifies. No peak duration figure is provided in the catalogue entries referenced here.

Specify your system

For full electrical and mechanical specifications or to discuss module selection for a specific pack architecture, review the MEB 590 and VDA battery module range at Avantis Energy or submit a technical question.

Next step · Avantis Energy

Building a pack on MEB 590?

Avantis Energy supplies prismatic NMC and LFP cells and complete modules in the MEB and VDA formats, so you integrate a certified module instead of validating your own. The catalogue lists 24 module types and 20 cell types.

Request a quote from Avantis EnergyTell us configuration, voltage and quantity. No account needed.

Or browse the full module range first