MEB 590 Battery Pack Design: 400 V and 800 V Systems

Short answer: A 2P8S MEB 590 module has a nominal voltage of 29.36 V. Fourteen modules in series produce approximately 411 V nominal, suitable for a 400 V system architecture. Twenty-eight modules in series produce approximately 822 V nominal, suitable for an 800 V architecture. Series count is set by the inverter voltage window; additional capacity comes from parallel strings.

Pack voltage in a battery-electric or stationary system is not a free variable. It is set by the inverter or power-conversion stage, which specifies a minimum and maximum DC bus voltage. The module count in series follows from that window, and additional energy capacity is added by connecting strings in parallel. This article works through both common targets, 400 V and 800 V, using a single reference module and showing each calculation step.

The reference module

The MEB 590 module specifications for the 2P8S configuration used throughout this article are as follows.

Parameter Value
Configuration 2P8S
Nominal voltage 29.36 V
Voltage window 22.4 V to 34.8 V
Capacity 227 Ah
Energy (gross) 6.66 kWh
Mass 31.4 kg
Dimensions (L x W x H) 590 x 225 x 110 mm
Continuous current at 1C 227 A
Cycle life at 80 % DoD 1,200 cycles

All figures are taken directly from the catalogue datasheet. Any parameter not listed here, such as peak current duration or thermal limits, should be taken from the same datasheet rather than assumed.

Why the inverter sets the series count

A traction or storage inverter accepts a DC bus voltage within a defined window. Operating outside that window, either too low during discharge or too high during charge, will cause the inverter to fault or to derate. The pack designer therefore works backward: take the inverter's minimum and maximum DC input voltage, divide each by the module's corresponding cell-level voltage limits, and the result is the allowable range of series modules.

For a nominal target, dividing the target bus voltage by the module's nominal voltage gives a first approximation of the series count. The voltage window of the resulting string must then be verified to sit within the inverter's acceptance range.

More capacity is never added by increasing the series count beyond what the voltage window allows. It is added by connecting complete strings in parallel, which keeps the voltage identical and multiplies the amp-hour capacity.

400 V system: 14 modules in series

Series count calculation: 400 V target divided by 29.36 V per module equals 13.6, rounded to 14 modules.

Resulting string parameters:

Parameter Calculation Result
Nominal voltage 14 x 29.36 V 411 V
Minimum voltage 14 x 22.4 V 314 V
Maximum voltage 14 x 34.8 V 487 V
Gross energy 14 x 6.66 kWh 93 kWh
Mass 14 x 31.4 kg 440 kg
Continuous current at 1C 227 A (string current) 227 A
Continuous power at 1C 227 A x 411 V approx. 93 kW

The voltage window of 314 V to 487 V is what the inverter must accept across the full state-of-charge range. Confirm this against the inverter datasheet before finalising the series count.

The 93 kWh figure is gross energy. Usable energy depends on the state-of-charge window the BMS applies. At 80 % depth of discharge, as stated for the 1,200-cycle rating, usable energy is approximately 74 kWh per string.

800 V system: 28 modules in series

Series count calculation: 800 V target divided by 29.36 V per module equals 27.3, rounded to 28 modules.

Resulting string parameters:

Parameter Calculation Result
Nominal voltage 28 x 29.36 V 822 V
Minimum voltage 28 x 22.4 V 627 V
Maximum voltage 28 x 34.8 V 974 V
Gross energy 28 x 6.66 kWh 187 kWh
Mass 28 x 31.4 kg 879 kg
Continuous current at 1C 227 A (string current) 227 A
Continuous power at 1C 227 A x 822 V approx. 187 kW

The maximum voltage at full charge, 974 V, is relevant for component insulation ratings, cabling specifications and safety interlock design. High-voltage systems above 800 V nominal require particular attention to creepage and clearance distances under standards such as IEC 62619, which covers safety requirements for secondary lithium cells and batteries used in stationary applications.

Adding capacity with parallel strings

Once the series count is fixed by the voltage target, capacity scales linearly with the number of parallel strings.

Strings in parallel Nominal voltage Gross energy Mass
1 (14S) 411 V 93 kWh 440 kg
2 (14S x 2P) 411 V 186 kWh 880 kg
3 (14S x 3P) 411 V 279 kWh 1,320 kg
1 (28S) 822 V 187 kWh 879 kg
2 (28S x 2P) 822 V 374 kWh 1,758 kg

Parallel strings raise additional engineering requirements. Current sharing between strings must be managed, because even small differences in state of charge or internal resistance between strings will drive circulating currents. Common approaches include passive balancing through matched string impedance, active string isolation using contactors per string, and BMS architectures that monitor each string independently. The appropriate approach depends on the application and the BMS specification, which should be established per project rather than assumed from the module specification alone.

For stationary storage applications, the MEB 590 module in energy storage systems article covers the broader context of using this format in grid-connected and behind-the-meter installations.

Format comparison: MEB 590 versus VDA 355

Engineers selecting a module format for a new pack design often compare the MEB 590 against the VDA 355. The table below summarises the key dimensional and electrical differences using the 2P8S MEB 590 reference and a representative VDA 355 configuration. VDA 355 figures vary by configuration; consult the relevant datasheet for the specific variant.

Parameter MEB 590 (2P8S) VDA 355 (typical 2P6S)
Length 590 mm 355 mm
Nominal voltage 29.36 V approx. 22 V
Capacity 227 Ah varies by cell
Energy per module 6.66 kWh approx. 2 to 4 kWh
Primary application Vehicle traction, stationary storage Vehicle traction

The MEB 590's larger cell count per module means fewer modules are needed to reach a given pack voltage and energy target, which can simplify busbar routing and reduce the number of inter-module connections. The 590 format overview covers the mechanical standardisation in more detail.

The EU Battery Regulation 2023/1542, published on EUR-Lex, introduces traceability and performance declaration requirements that apply to batteries placed on the European market. Pack designers working with MEB 590 modules should account for these documentation requirements early in the design process.

Frequently asked questions

How many MEB 590 modules in series for a 400 V battery pack?
Using the 2P8S reference module at 29.36 V nominal, 14 modules in series give approximately 411 V nominal with a voltage window of 314 V to 487 V. This is the series count to target for a nominal 400 V system architecture, subject to verification against the inverter's DC input specification.

How many MEB 590 modules in series for an 800 V battery pack?
Twenty-eight modules in series give approximately 822 V nominal with a voltage window of 627 V to 974 V. The 974 V maximum at full charge must be within the insulation and component ratings of all pack elements, including cabling, contactors and the inverter DC input.

What is the gross energy of a 14-module MEB 590 string?
Fourteen 2P8S modules each rated at 6.66 kWh give 93 kWh gross per string. Usable energy at 80 % depth of discharge is approximately 74 kWh. The cycle life rating of 1,200 cycles is stated at 80 % DoD, so that figure should be used as the sizing basis.

How is additional capacity added without changing pack voltage?
Capacity is added by connecting complete strings in parallel. Each additional parallel string multiplies amp-hour capacity and gross energy while keeping nominal voltage unchanged. Parallel strings require current-sharing management and, typically, independent string monitoring within the BMS architecture.

Does module series count alone determine pack power?
No. Continuous power is the product of string current and string voltage. At 1C the reference module delivers 227 A. A 14-module string at 411 V nominal gives approximately 93 kW continuous; a 28-module string at 822 V gives approximately 187 kW. Higher power requires either a higher C-rate, confirmed from the datasheet, or additional parallel strings.

Specify your pack

For detailed module specifications and to discuss series or parallel configurations for your application, review the MEB 590 modules available from Avantis Energy or contact the technical team directly.

Next step ยท Avantis Energy

Building a pack on MEB 590?

Avantis Energy supplies prismatic NMC and LFP cells and complete modules in the MEB and VDA formats, so you integrate a certified module instead of validating your own. The catalogue lists 24 module types and 20 cell types.

Request a quote from Avantis EnergyTell us configuration, voltage and quantity. No account needed.

Or browse the full module range first